Outdoor · Masonry

Concrete Block Calculator

Blocks by course, mortar bags from the manufacturer’s yield, and grout for filled cores, for any wall length and height.

1 Wall
ft
ft
ft²
Units
2 Block
%
Blocks
95
90 net + 5%
Courses
6
15 blocks per course
Mortar
7bags
80 lb, ≈13 blocks per bag
Core fill
—
Not grouted
1.125 blocks per square foot of wall face. Height is rounded up to whole courses (4.00 ft built height); adjust with a half-high top course if you need an exact height.

Block wall list

Block wall list
ItemQtyNotes
Concrete block 16×8×8 in.95
Mortar mix, 80 lb bags7
Footing not included: size it with the concrete calculator (wall footing mode).

How the block count works

Area-based counts (wall area × 1.125) are fine for a budget but wrong for an order, because walls are built in whole courses and every course ends where the wall ends. The calculator counts the way a mason lays out: courses = wall height ÷ unit height, rounded up; blocks per course = wall length ÷ unit length, rounded up. It then takes out whole blocks for openings and adds your breakage allowance.

Courses = ceil(height × 12 ÷ unit height) Blocks/course = ceil(length × 12 ÷ unit length) Mortar bags = blocks ÷ 13 (80 lb QUIKRETE Mortar Mix, 8×8×16 units) Core volume = (L − ⅜)(T − ⅜)(H − ⅜) × (1 − solid fraction) ÷ 1728 [ft³ per block]

Worked example: a 40 × 4 ft garden wall

  • Courses: 48 ÷ 8 = 6. Per course: 480 ÷ 16 = 30. Net blocks: 180; with 5% breakage, 189.
  • Mortar: 180 ÷ 13 = 13.8, so 14 bags of 80 lb.
  • Core fill at rebar cells every 48 in.: one cell in six of 0.25 ft³ per block = 7.6 ft³, or 14 bags of 80 lb concrete with a 10% allowance.

Before you build

  • Footing first. A block wall sits on a concrete footing below the frost line. Size it with the wall-footing mode of the concrete calculator; the IRC sets a 6 in. minimum footing thickness (R403.1.1).
  • Retaining soil changes everything. A wall that holds back soil needs drainage, reinforcement and often engineering. For landscape walls, segmental retaining-wall units are designed for that job; see the retaining wall calculator.
  • Check the unit’s data sheet. Hollow units under ASTM C90 vary in how solid they are. The solid percentage on the manufacturer’s sheet drives the grout estimate.

Common mistakes

  • Forgetting corners and ends. If you need clean ends, order corner (or bullnose) units separately; they replace regular blocks one for one.
  • Ordering exactly. Blocks chip in delivery and cutting; 5% spare is normal, 10% for walls with many openings.
  • Mixing too much mortar at once. Mortar has a working life; mix what you can lay before it stiffens and don’t re-temper it more than the bag allows.

Laying out the first course

Dry-lay the first course on the footing before mixing mortar. Adjust the head joints slightly so the wall ends on a full or half block instead of a sliver; it saves cutting and looks better. Snap a line for the face of the wall, set the corner or end blocks first, level and plumb them, then string a line between them for every course. Check each corner for plumb and the wall for level every two or three courses; small errors in the first courses are visible at the top.

Block walls need time: mortar has to stiffen before the next few courses go on, and grouted cells should be filled in lifts the reinforcement design allows. In cold weather, protect fresh work from freezing.

Questions people ask

How many concrete blocks per square foot?
A standard 8×8×16 in. block covers 128 in² of wall face including its mortar joint, so you need 1.125 blocks per square foot. Half-high 16×4 in. units need 2.25 per square foot.
How many blocks are in a 4 ft high, 40 ft long wall?
Six courses of 8 in. block reach 4 ft, and each 40 ft course takes 30 blocks of 16 in., so 180 blocks, plus about 5% for breakage and cuts: 189.
How much mortar do I need for block?
QUIKRETE’s data sheet says one 80 lb bag of its Mortar Mix lays about 13 standard 8×8×16 blocks. That is 14 bags for 180 blocks. Thick joints, cold weather and waste on the board use more.
How much grout fills the cores?
An 8 in. hollow block that is 52% solid has about 0.25 ft³ of open cells. Filling every cell of 180 blocks takes about 45 ft³ (1.7 yd³); grouting only the rebar cells every 48 in. fills one cell in six, about 7.6 ft³.
What does “nominal size” mean for block?
Blocks are made 3/8 in. smaller than their name so a mortar joint brings them to the round number: an 8×8×16 is really 7⅝ × 7⅝ × 15⅝ in. Count blocks with nominal sizes; compute core volume with actual sizes.

Sources

  1. QUIKRETE Mortar Mix data sheet (No. 1102) — QUIKRETE, checked Nov 2026. One 80 lb bag lays about 13 standard 8×8×16 in. blocks or 37 bricks.
  2. ASTM C90: Standard Specification for Dry-Cast Loadbearing Concrete Masonry Units — ASTM International, checked Nov 2026.
  3. 2021 International Residential Code (IRC) — International Code Council, checked Nov 2026.

Related calculators

All outdoor tools →