Framing · IRC R507.6

Deck Joist Span Calculator

Pick your species, size and spacing to get the allowed span and cantilever. Enter your deck’s span to see the smallest joist that works.

1 Code & lumber
Treated lumber is usually southern pine in the East and South, hem-fir or Douglas fir in the West. Check the stamp.
Joist size
Spacing (on center)
2 Your deck
ft
Ledger face to beam center
in
Past the beam
ft
Max span
11′-10″
2x8 @ 16″, Southern pine
Max cantilever
2′-3″
2021 IRC Table R507.6
Your span
11′ 10″
100% of allowed
Joists
13
for 16′ at 16″ o.c.
2x8 joists at 16″ o.c. are within 2021 IRC Table R507.6 for a 11′ 10″ span (40 psf live). This is not a permit approval.
SpacingSmallest joist within the table
12″ o.c.2x8
16″ o.c.2x8
24″ o.c.2x12

2021 IRC Table R507.6: Southern pine

40 psf live
Size12″ span16″ span24″ spanCant. 4 ft back spanCant. 6 ft back spanCant. 8 ft back spanCant. 10 ft back spanCant. 12 ft back spanCant. 14 ft back spanCant. 16 ft back spanCant. 18 ft back span
2x69′-11″9′-0″7′-7″1′-0″1′-6″1′-5″NPNPNPNPNP
2x813′-1″11′-10″9′-8″1′-0″1′-6″2′-0″2′-6″2′-3″NPNPNP
2x1016′-2″14′-0″11′-5″1′-0″1′-6″2′-0″2′-6″3′-0″3′-4″3′-4″NP
2x1218′-0″16′-6″13′-6″1′-0″1′-6″2′-0″2′-6″3′-0″3′-6″4′-0″4′-1″
Southern pine. No. 2 grade, wet service, 10 psf dead load, L/360 (cantilever L/180 with a 220 lb point load). Values are from the official 2021 IRC table. Cantilever limits are by joist back span; we read the lower bracketing column instead of interpolating. Cantilevers are also limited to ¼ of the back span. Struck-through spans are shorter than yours. NP = not permitted.

Reading the joist span table

IRC Table R507.6 gives the longest span allowed for each joist size and spacing, for three species groups. The span is measured from the face of the ledger (or the centerline of the supporting beam) to the centerline of the beam at the far end. It doesn’t include the cantilever past the beam. The table assumes:

  • 40 psf live load plus 10 psf dead load, which is a normal residential deck with no hot tub and ground snow load of 40 psf or less;
  • No. 2 grade lumber, adjusted for wet service, with an incising factor for treated southern pine;
  • a deflection limit of L/360 on the main span and L/180 on the cantilever, which is also checked with a 220 lb load at its tip.

The 2021 IRC adds rows for 50, 60 and 70 psf ground snow loads, and limits cantilevers by the joist’s back span rather than by spacing. Choose the edition your building department uses and your snow load. The calculator reads the matching official table.

Where reproductions of the table disagree

Published copies of this table don’t all match. Three 2x6 cells differ between sources, for example Douglas fir 2x6 at 16″ shows as 8′-4″ in some and 8′-8″ in others. In each case we use the shorter span. The methodology lists every cell and source, and the full tables are on the deck span tables page.

Span isn’t the only limit

Decking manufacturers set their own maximum joist spacing, commonly 16″ on center for composite boards and 12″ for diagonal layouts, and that is usually stricter than the framing table. A deck that is code-legal at 24″ spacing may void a board warranty. Check the board spec sheet before choosing spacing. See deck joist spacing for more.

Mistakes that make a legal span feel bouncy

  • Measuring the wrong span. The table span runs from the face of the ledger to the centerline of the beam, not the overall deck depth. A cantilever past the beam is checked separately, and it can’t exceed a quarter of the back span.
  • Mixing species groups. Southern pine, Douglas fir-larch, hem-fir and redwood/cedar have different allowable spans. If the tag isn’t legible, use the most restrictive group (the calculator’s “not sure” option).
  • Notching and boring. Joists notched over a beam or drilled for wiring lose capacity the tables don’t account for. Hang joists or sit them fully on the beam.
  • Crowns pointing different ways. Sight down every joist and install the crown (the slight hump) up; mixed crowns telegraph through the decking.

Choosing between a deeper joist and closer spacing

If a 2×8 at 16 in. doesn’t reach, you can step up to a 2×10 at 16 in. or keep the 2×8 at 12 in. The deeper joist usually wins: fewer pieces, fewer hangers and fasteners, and a stiffer floor. Closer spacing makes sense when the decking requires it anyway: many composite boards need 12 in. spacing on diagonal layouts, and some thin boards need it straight. Check the decking maker’s span rating before you settle the framing, then confirm the joist size here.

Questions people ask

How far can a 2x8 deck joist span?
Under IRC Table R507.6, a 2x8 at 16″ on center spans 11′-10″ in southern pine, 11′-1″ in Douglas fir-larch, hem-fir or spruce-pine-fir, and 10′-7″ in redwood, western cedar, ponderosa or red pine. At 12″ on center: 13′-1″, 12′-6″ and 11′-8″.
How far can a 2x10 deck joist span?
At 16″ on center: 14′-0″ (southern pine), 13′-7″ (Douglas fir / hem-fir / SPF), 13′-0″ (redwood / cedar). At 12″ on center: 16′-2″, 15′-8″ and 14′-11″.
How far can a 2x12 deck joist span?
At 16″ on center: 16′-6″ (southern pine), 15′-9″ (Douglas fir / hem-fir / SPF), 15′-1″ (redwood / cedar). At 12″ on center the table caps southern pine and Douglas fir at 18′-0″.
How far can deck joists cantilever?
The IRC table lists a maximum cantilever for each size and spacing (for example 3′-6″ for southern pine 2x10 at 16″). The cantilever also can’t exceed one quarter of the actual back span. Where joists cantilever, blocking or other lateral restraint is required over the beam.
Which species is my pressure-treated lumber?
Read the grade stamp or end tag. In the eastern and southern US, treated framing is usually southern pine (SYP). In the West it is often hem-fir or Douglas fir. If the stamp doesn’t name the species, use the most conservative group.

Related calculators

All deck tools →