Interior · Insulation

Insulation & R-Value Calculator

From your climate zone’s R-value target to the depth, the batts or bags, the spray-foam board feet, and the installed cost.

Costs checked: November 2026Code basis: 2021 IECC Table R402.1.3Sources

1 Attic or wall
ft²
Attic floor ≈ the home’s top-floor footprint
Inches of old fiberglass × about 3
2 Insulation
3 Location and labor

Region factor ×1.00: U.S. national average. How it’s derived

Who does the work
Low
$600
Typical
$1,450
$1.45 per ft²
High
$2,300
Region
×1.00
U.S. national average
Cost breakdown
ItemQuantityLowTypicalHigh
Blown-in cellulose1,000 sq ft$600$1,450$2,300
Split
Materials$360$870$1,380
Labor, equipment & overhead$240$580$920
Total installed$600$1,450$2,300
Adding R-49 of blown-in cellulose takes about 14.0 in. . The 2021 IECC (Table R402.1.3) and ENERGY STAR call for R-60 in zone 5 attics. The bag’s coverage chart, required by the FTC R-value rule, governs real depth and bag count.

Costs checked: November 2026. Ranges are published national figures (see Sources below) times the regional factor. They exclude permits, sales tax and unusual site work. Get at least three local quotes.

Insulation to buy

Insulation to buy
ItemQtyNotes
Blown-in cellulose1,167 ft³ installed14.0 in. settled depth; bags list ft² per bag at each R
Rafter vents / bafflesone per rafter bay at the eaves

How the calculator works

Insulation is specified by R-value, the resistance to heat flow, and R-values add. Pick your climate zone to load the 2021 IECC ceiling target, enter what’s already there, and the calculator works out the R-value to add and the thickness it takes for the material you choose. Spray foam is converted to board feet, the unit it is priced in.

R to add = target R − existing R Depth (in.) = R to add ÷ R per inch Board feet = area × depth (spray foam) Volume (ft³) = area × depth ÷ 12 (blown-in) Cost = area (or board feet) × published $ × regional factor

R per inch is a typical value for each material (blown fiberglass ≈ 2.5, cellulose ≈ 3.5, fiberglass batts ≈ 3.2, mineral wool ≈ 4, open-cell foam ≈ 3.6, closed-cell foam ≈ 6.5), within the ranges published by the Department of Energy and Fixr. The FTC R-value rule requires every bag of insulation to carry a coverage chart, and that chart is the authority for your product.

Worked example: a 1,000 ft² attic in climate zone 5

  • Target R-60. Existing: about 3½ in. of old fiberglass, roughly R-11. Add R-49.
  • Blown cellulose at R-3.5/in.: 14 in. settled depth, about 1,170 ft³.
  • Or batts: one layer of R-38 plus one of R-11 laid across the joists.
  • Installed cost, cellulose: 1,000 × $0.60 / $1.45 / $2.30 = $600 / $1,450 / $2,300, about 40% labor.
  • Spray foam alternative: closed-cell over 500 ft² of rim joists and walls at 2 in. is 1,000 board feet, $1,000–$2,000.

Air seal first

Insulation slows heat moving through materials; it doesn’t stop air leaking through gaps. Before adding attic insulation, seal top plates, wiring and plumbing holes, the attic hatch and recessed lights rated for contact. Install baffles at the eaves so insulation doesn’t block soffit vents, and keep the required clearances around chimneys and flues.

Common mistakes

  • Compressing batts. A crushed R-19 batt doesn’t give R-19.
  • Covering soffit vents, which traps moisture in the attic.
  • Adding faced batts over existing insulation, which traps moisture between layers.
  • Blowing to the depth you want before it settles. Check the chart for initial and settled thickness and mark depth rulers across the attic.

DIY or hire?

Blowing loose-fill into an open attic is a common DIY job, and many stores loan the blowing machine with a minimum bag purchase. Spray foam is a professional job: it needs proper equipment, protective gear and ventilation.

Questions people ask

What R-value do I need in my attic?
The 2021 IECC (Table R402.1.3) calls for R-30 ceilings in climate zone 1, R-49 in zones 2–3 and R-60 in zones 4–8, which matches ENERGY STAR’s targets for uninsulated attics. Your local code may still be on an older edition; check with the building department for new work.
How many inches of insulation for R-60?
Divide the R-value by R per inch: about 17 in. of blown cellulose (R-3.5/in.), or 24 in. of blown fiberglass (R-2.5/in.). The bag’s coverage chart, required by the FTC R-value rule, gives the exact settled thickness and bags per 1,000 ft² for that product.
How much does attic insulation cost?
Fixr’s 2026 installed ranges per ft²: blown-in or loose-fill $0.50–$2.30, cellulose $0.60–$2.30, batts and rolls $0.30–$2.10, and spray foam $1–$4.50. Fixr says labor is 30–50% of the total, and removing old insulation adds $1–$3 per ft².
How much does spray foam insulation cost?
Spray foam is sold by the board foot (1 ft² × 1 in. thick). Homeyou puts open-cell at about $0.30–$0.50 and closed-cell at $1–$2 per board foot. Closed-cell gives about R-6.5 per inch, open-cell about R-3.6, so closed-cell costs more per board foot but needs fewer inches.
Can I add insulation over old insulation?
Usually yes, if the old insulation is dry and not contaminated: subtract its R-value from the target and add the difference. Unfaced batts or loose fill go over the top; never add a second vapor retarder (facing) on top of existing insulation.

Sources

Costs checked: November 2026. Each range is the published figure from the source named next to it; where we did arithmetic on a published figure the page says so. Regional factors: how they’re derived.

  1. 2021 International Energy Conservation Code, Table R402.1.3 — International Code Council, checked Nov 2026.
  2. Recommended Home Insulation R-Values — ENERGY STAR (U.S. EPA), checked Nov 2026.
  3. Guide to Home Insulation — U.S. Department of Energy, checked Nov 2026.
  4. R-Value Rule, 16 CFR Part 460 (labeling and coverage charts on insulation) — U.S. Federal Trade Commission / eCFR, checked Nov 2026.
  5. How Much Does It Cost to Insulate a Home? — Fixr, checked Nov 2026.
  6. Insulation Cost — Homeyou, checked Nov 2026. Spray foam per board foot: open-cell about $0.30–$0.50, closed-cell about $1–$2.
  7. Cost vs. Value 2025: national and regional data — Remodeling magazine / Zonda (JLC), checked Nov 2026. Job costs for 13 projects in 9 Census divisions; used for regional factors and benchmark projects.

Related calculators

All interior tools →