Deck · Fasteners

Deck Screw & Fastener Calculator

Every fastener on the deck: decking screws or hidden clips, joist hangers and their nails, ledger lags or bolts at code spacing, and joist tape.

Code basis: 2021 IRC R507.9, R317.3Sources

1 Deck
ft
ft
2 Fastening
Decking fasteners
%
From the hanger’s spec
Deck screws
710
13 joists × 26 rows = 338 crossings
Joist hangers
11
110 hanger nails
Ledger fasteners
14
15 in. o.c., staggered (2021 IRC Table R507.9.1.3(1))
Joist tape
188ft
4 rolls of 50 ft
1.76 board-to-joist crossings per ft². Use the screws or clips the decking maker specifies: composite and PVC warranties usually require their own fasteners.

Fastener list

Fastener list
ItemQtyNotes
Deck screws (coated or stainless)7103 × 350-count
Joist hangers11sized to your joists
Hanger nails or connector screws110exactly the type the hanger lists
½ in. lag screws with washers14
Butyl joist tape4 rolls (50 ft)
Corner brackets or angles for rim joists2
Fasteners and connectors in contact with treated lumber need hot-dip galvanized or stainless finishes (IRC R317.3).

How fasteners are counted

Per-square-foot rules of thumb drift with joist spacing and board width. The calculator counts the real thing: joists from the deck width and spacing, rows of boards from the depth and board width plus gap, and the crossings where they meet. Every other number follows from those.

Joists = ceil(width × 12 ÷ spacing) + 1 Rows = ceil(depth × 12 ÷ (board width + gap)) Crossings = joists × rows Screws = crossings × screws per joist × (1 + spare) Clips = crossings × (1 + spare) + starter clips (one per joist) Hangers = joists − 2 (per hanger line) Ledger = width × 12 ÷ IRC spacing + 1

Worked example: 16 × 12 ft attached deck

  • Joists at 16 in.: 192 ÷ 16 + 1 = 13. Rows of 5½ in. boards with a 3/16 in. gap: 144 ÷ 5.6875 = 25.3 → 26. Crossings: 338.
  • Face screws: 676 + 5% = 710, about three 350-count boxes.
  • Joist hangers at the ledger: 11; at 10 nails each, 110 hanger nails (use the count on your hanger’s spec sheet).
  • Ledger with ½ in. lags and a 12 ft joist span: 15 in. on center (2021 IRC Table R507.9.1.3(1)) → 14 lags.
  • Joist tape: 13 joists × 12 ft + both rims = 188 ft, four 50 ft rolls.

Fastener rules that matter

  • Corrosion: treated lumber corrodes plain steel. Use hot-dip galvanized (G185) or stainless connectors and fasteners, and don’t mix galvanized and stainless in one connection.
  • Hanger nails are not deck screws: fill every hole in a hanger with the exact nail or structural screw the manufacturer lists. Deck screws are brittle in shear and aren’t rated for hangers.
  • Ledger attachment: lags or bolts go through the ledger into the house band joist, staggered top and bottom, never into brick veneer or an overhang. The planner and the joist span calculator show the spacing for your span.
  • Lateral load connection: the IRC also requires a lateral connection between the deck and the house (R507.9.2), typically hold-down devices at the ends of joists.

Tips

  • Pre-drill near board ends in hardwood and dense composite to avoid splitting and mushrooming.
  • Keep screws in line with a chalk line or a spacer jig; the eye notices a wandering row.
  • Joist tape on the tops of joists and beams sheds water from the place wood rots first.

Buying tips

Buy fasteners in the largest box you will use: deck screws in 1,750-count buckets cost much less per screw than 350-count boxes, and leftover screws keep. For colored composite screws, buy the exact color code the decking maker lists so the heads blend in.

Questions people ask

How many deck screws do I need?
Two screws at every place a board crosses a joist. A 16 × 12 ft deck with 5½ in. boards and joists 16 in. on center has 13 joists and 26 rows of boards: 338 crossings, so 676 screws, about 710 with 5% spare. That is about 3.5 screws per square foot.
How many hidden clips per square foot?
One clip per board per joist, so about 1.6 per ft² at 16 in. joist spacing with 5½ in. boards, and about 2.1 at 12 in. spacing. Add starter clips along the first board. The deck above needs about 355 clips plus 13 starters.
How many joist hangers do I need?
One at the ledger end of every joist except the two rim joists, which are fastened with corner brackets or angles. Add another set if the joists hang from a flush beam at the other end.
How far apart should ledger lag screws be?
It depends on the joist span: for ½ in. lag screws, 2021 IRC Table R507.9.1.3(1) allows 30 in. on center for joist spans up to 6 ft, 18 in. at 10 ft, 15 in. at 12 ft and 10 in. at 18 ft (40 psf). Through-bolts allow wider spacing. Fasteners are staggered in two rows.
Do I need special screws for composite decking?
Use the screws or hidden fasteners the decking maker specifies; most composite and PVC warranties require them. For treated lumber, fasteners must be hot-dip galvanized, stainless or otherwise approved for contact with preservative-treated wood (IRC R317.3).

Sources

  1. 2021 International Residential Code (IRC) — International Code Council, checked Nov 2026.
  2. DCA 6: Prescriptive Residential Wood Deck Construction Guide — American Wood Council, checked Nov 2026.

Related calculators

All deck tools →