Finishing

Deck Stain Calculator

Gallons for the deck floor, railings and stairs, using the coverage printed on your can, plus the cheapest mix of pails and single gallons.

1 Surfaces
ft
ft
ft
0 if not staining
in
sq ft
2 Product
ft²
Labels often list 150–300 ft² on rough or weathered wood and more on smooth new wood. Use the low end for older decks.
Coats
Stain needed
3.6gal
452 ft² × 2 coats
Buy
1×5 gal
4+ single gallons → one 5-gal pail
Deck floor
192ft²
Railings
240ft²
Both faces, as a solid panel
Coverage varies far more by wood than by brand. New, smooth boards absorb little, while weathered or rough-sawn wood can take twice as much. Before you buy, do a test patch and check the label for the coat count and the recoat window.

Railing area counts the railing as a solid panel on both faces, which slightly overestimates baluster railings. Composite and PVC decking is not stained.

Why we ask for your label’s coverage

Coverage claims vary widely from product to product, and even more with the condition of the wood. A new, smooth board absorbs a fraction of what a gray, weathered or rough-sawn board soaks up. So this calculator doesn’t guess. It uses the number on your can, and for older decks we suggest the low end of the label’s range.

Getting the area right

  • Floor: width × depth.
  • Railings: we count each railing as a solid panel on both faces (length × height × 2). Balusters and rails have less surface than a solid panel, but the edges and the overlap from brushing make up much of the difference, and it errs toward having enough.
  • Stairs: add the treads, risers and the outside face of the stringers.
  • Edges: if you will brush stain onto the board edges, tick the option. It adds about 36% of the floor area for 5½″ × 1″ boards.

Worked example: a 16 × 12 ft deck with railings and stairs

  • Deck floor 192 ft².
  • 40 ft of 36 in. railing, both faces as a panel: 40 × 3 × 2 = 240 ft².
  • Stairs (treads, risers and stringer faces): about 20 ft².
  • Total 452 ft² × 2 coats ÷ 250 ft² per gallon = 3.6 gallons: four 1-gallon cans, or one 5-gallon pail, which is usually cheaper and avoids color differences between cans.

Preparation decides how much you use

Clean, dry, slightly weathered wood takes stain evenly. New pressure-treated lumber is often too wet to absorb it; many stain makers recommend waiting until a few drops of water soak in rather than bead up. Old, gray or rough wood drinks far more stain than smooth new boards, so the low end of the label’s coverage range is the safer number for an older deck.

Choosing a product

  • Clear and toner finishes show the wood but need recoating most often.
  • Semi-transparent stains add color and UV protection while showing the grain; the most common choice.
  • Solid stains hide the grain and last longer on vertical surfaces, but can peel on walking surfaces.

Common mistakes

  • Applying a second coat after the first has sealed the wood; many penetrating stains want wet-on-wet coats within a set window. Read the label.
  • Staining in direct sun or before rain; lap marks and wash-off waste product.
  • Forgetting the end grain and the board edges, where water gets in first.

How often to restain

Horizontal surfaces wear fastest. Many semi-transparent stains need a maintenance coat on the deck floor every two to three years, while railings and vertical surfaces last longer. A simple test: sprinkle water on the boards. If it soaks in quickly and darkens the wood, it’s time to clean and recoat. Use the same calculator for the maintenance coat, usually with one coat instead of two.

Composite and PVC decks

Capped composite and PVC boards aren’t stained. Clean them with the maker’s recommended cleaner. If you have a wood frame with composite decking, you may still stain wood railings, fascia and stair stringers; set the deck floor to zero and enter only those areas.

Questions people ask

How much stain do I need for a 12x16 deck?
The floor is 192 sq ft. At 250 sq ft per gallon, two coats take about 1.5 gallons for the floor alone. Add railings (about 6 sq ft per foot of railing, both faces) and stairs. Use the calculator with your product’s label coverage.
How many square feet does a gallon of deck stain cover?
It depends on the product and the wood. Labels commonly list around 150–300 sq ft per gallon on rough or weathered wood, and more on smooth new wood. Second coats usually go further than the first. Always use the coverage printed on your can.
Should I buy 1-gallon cans or a 5-gallon pail?
If you need four or more gallons, a 5-gallon pail is usually cheaper and keeps the color consistent across the job. For smaller jobs, buy single gallons and box (mix) them together before you start.

Related calculators

All deck tools →