Framing · Stairs

Stair Stringer Calculator

Risers, treads, flights and stringer length for any stair, straight or with a landing or L-turn, plus the framing-square marks and every IRC check.

Code basis: 2021 IRC R311.7Sources

1 Stair
in
in
10 in. minimum (IRC)
in
7¾ in. under the IRC
in
Units
2 Landing
Landing
Risers
14
7 11/16″ each
Treads
13
10 1/2″ run
Footprint
11′ 4 1/2″
× 3′ wide
Angle
36.3°
2R + T = 25.93 in. (outside 24–25½)
Flights
FlightRisersTreadsRiseRunStringer
Single14139′11′ 4 1/2″15′ 2 7/16″
  • ✓Riser heightIRC R311.7.5.1: 7¾ in. maximumwithin
  • ✓Tread depthIRC R311.7.5.2: 10 in. minimumwithin
  • ✓Stair widthIRC R311.7.1: 36 in. minimum clear above the handrail heightwithin
  • ✓Rise per flightIRC R311.7.3: 151 in. maximum between floors or landingswithin
  • ✓Stringer throatAWC DCA 6 (exterior cut stringers): at least 5 in. after notchingwithin
Framing-square layout (lower flight): set the square at 7 11/16″ rise and 10 1/2″ run
  • 1: run 10 1/2″ · rise 7 11/16″
  • 2: run 1′ 9″ · rise 1′ 3 7/16″
  • 3: run 2′ 7 1/2″ · rise 1′ 11 1/8″
  • 4: run 3′ 6″ · rise 2′ 6 7/8″
  • 5: run 4′ 4 1/2″ · rise 3′ 2 9/16″
  • 6: run 5′ 3″ · rise 3′ 10 5/16″
  • 7: run 6′ 1 1/2″ · rise 4′ 6″
  • 8: run 7′ · rise 5′ 1 11/16″
  • 9: run 7′ 10 1/2″ · rise 5′ 9 7/16″
  • 10: run 8′ 9″ · rise 6′ 5 1/8″
  • 11: run 9′ 7 1/2″ · rise 7′ 7/8″
  • 12: run 10′ 6″ · rise 7′ 8 9/16″
  • 13: run 11′ 4 1/2″ · rise 8′ 4 5/16″
  • 14: run 12′ 3″ · rise 9′
Cut the bottom of each stringer short by one tread thickness so the first riser matches the rest. Headroom must be at least 6 ft 8 in. along the whole flight (IRC R311.7.2), and with 4 or more risers you need a handrail 34–38 in. high (R311.7.8).

Stair framing

Stair framing
ItemQtyNotes
Stringers, 2×12 (single flight)415′ 2 7/16″ each; buy the next stock length
Treads133′ wide
Stringers at 16 in. o.c. here; exterior cut stringers may be up to 18 in. o.c. (DCA 6) unless the tread maker requires less.

How the stair is laid out

A stair is a set of equal steps that has to fit an exact height. The riser height therefore comes from the total rise, not the other way round: the calculator divides the rise into the fewest risers that stay under your maximum, so every riser is identical. Treads are one fewer than risers because the upper floor is the last step. With a landing, the risers split into two flights and the landing takes the place of one tread.

landing ≥ 36 in.flight 1flight 2runeach flight ≤ 151 in. of rise
Two flights and a landing. Each flight may rise at most 151 in.; the landing is at least 36 in. deep.
Risers = ceil(total rise ÷ max riser) Riser height = total rise ÷ risers Treads = risers − 1 (− 1 more per landing) Run (flight) = treads in flight × tread depth Stringer = √(flight rise² + (flight run + one tread)²) Throat = stringer depth − riser × tread ÷ √(riser² + tread²)

Worked examples

Basement stair, 108 in. rise: 14 risers of 7 23/32 in., 13 treads of 10½ in., total run 136½ in. Each 2×12 stringer is about 15 ft 2 in. long, so buy 16 ft boards; the throat left after notching is 5 in., just meeting DCA 6’s minimum for exterior cut stringers.

Tall deck stair, 160 in. rise: one flight would rise 160 in., over the 151 in. limit. With a straight landing: 21 risers of 7.62 in., split 11 below and 10 above the landing; 19 treads; total footprint 105 + 36 + 94½ = 235½ in. As an L-turn the same stair fits in 141 × 130½ in.

Cutting the stringer

  • Clamp stair gauges (or a block) to a framing square at the riser and tread dimensions and step the pattern along the board, crown edge up.
  • Trim the bottom of the stringer by one tread thickness so the first riser comes out the same height as the rest once treads are on.
  • Cut the notches with a circular saw and finish the inside corners with a handsaw rather than over-cutting, which weakens the throat.
  • Cut one stringer, test it in place, then use it as the pattern for the others.

Code checks (2021 IRC R311.7)

  • Riser 7¾ in. maximum, tread 10 in. minimum, with no more than ⅜ in. variation within a flight.
  • Width at least 36 in.; headroom at least 6 ft 8 in. measured from the nosing line.
  • A handrail on at least one side where there are four or more risers, 34–38 in. above the nosings.
  • Landings at the top and bottom of every stair, and between flights, at least as wide as the stair and 36 in. deep.

Some states amend these limits (for example a taller riser). Check with your local building department. For deck stairs specifically, the deck stair calculator adds tread boards and a scale drawing; for a concrete pad at the bottom, use the concrete calculator.

Questions people ask

How do I calculate stair stringers?
Divide the total rise by the maximum riser (7¾ in. under the IRC) and round up for the number of risers; divide the rise by that number for the exact riser height. Treads are one fewer than risers. The stringer length is the diagonal of the total rise and the total run plus one more run for the bottom seat.
When do stairs need a landing?
IRC R311.7.3 limits a single flight to 151 in. (12 ft 7 in.) of vertical rise between floors or landings. Taller stairs need an intermediate landing at least as wide as the stair and 36 in. deep in the direction of travel (R311.7.6). Landings are also used to turn a stair 90° when there isn’t room for a straight run.
How many steps for a 9 ft ceiling?
With a 9 ft floor-to-floor rise of 108 in.: 108 ÷ 7.75 = 13.9, so 14 risers of 7.71 in. and 13 treads. With 10½ in. treads the stair runs 136½ in. (11 ft 4½ in.) horizontally.
What is a comfortable stair?
A long-standing rule of thumb is that twice the riser plus the tread (2R + T) should be about 24–25 in. A 7¼ in. riser with a 10½ in. tread gives 25 in. The IRC sets the limits (7¾ in. riser max, 10 in. tread min); comfort usually sits a little inside them.
How far apart should stringers be?
Exterior cut stringers may be up to 18 in. on center under the AWC DCA 6 guide, but many tread products require 12 in. or 16 in. A 36 in. stair typically uses three or four stringers. Interior stairs commonly use three stringers for a 36 in. width.

Sources

  1. 2021 International Residential Code (IRC) — International Code Council, checked Nov 2026.
  2. DCA 6: Prescriptive Residential Wood Deck Construction Guide — American Wood Council, checked Nov 2026.

Related calculators

All deck tools →