Outdoor · Hardscape

Paver Calculator

Pavers by size and pattern, then everything under and around them: base gravel, bedding sand, edging, spikes and joint sand.

1 Area
Shape
ft
ft
Units
2 Pavers
3 Base, sand and edging
in
in
ft
No edging needed there
ft²/bag
From the bag’s chart for your joint width
Pavers
126
1.00 per ft² + 5%
Base gravel
1.70yd³
2.6 tons, 4 in. + 15% compaction
Bedding sand
0.37yd³
20 bags of 0.5 ft³
Edging
44ft
45 spikes at 12 in.
120 ft² of pavers. Buy the same production lot (check the pallet tags) so the color matches, and keep a few spares for repairs.

Paver patio list

Paver patio list
ItemQtyNotes
Pavers 12×12 in.126120 ft² + 5% waste
Crushed-stone base (¾ in. minus)1.75 yd³2.6 tons
Concrete sand for bedding20 bags (0.5 ft³)or 0.37 yd³ bulk
Edge restraint44 ft
Edging spikes45
Polymeric joint sand3 bags
Geotextile fabric (on clay soils)132 ft²

How the paver calculator works

A paver patio is a layered system, and each layer is its own quantity. The pavers are counted from the face size, which already allows for the small spacer nubs on most concrete pavers. Under them sits a screeded inch of bedding sand, and under that a compacted crushed-stone base. Around the outside, edge restraint keeps the whole field from spreading.

Pavers = area × 144 ÷ (length × width) × (1 + pattern waste) Base = area × base depth ÷ 12 × 1.15 (compaction) ÷ 27 [yd³] Sand = area × 1 ÷ 12 [ft³] Edging = perimeter − edges against the house Spikes = edging length ÷ 12 in. + 1

Worked example: a 14 × 12 ft patio of 12 in. pavers

  • Area 168 ft². 12 × 12 in. pavers are 1 per ft²: 168 + 5% = 177 pavers.
  • Base: 168 × 4 ÷ 12 = 56 ft³ + 15% compaction = 64.4 ft³ = 2.39 yd³ (about 3.6 tons at 1.5 t/yd³).
  • Bedding sand: 14 ft³, 28 bags of 0.5 ft³.
  • Edging: perimeter 52 ft minus 14 ft along the house = 38 ft, with 39 spikes.
  • The same patio in 4 × 8 in. holland stones laid herringbone: 168 × 4.5 × 1.10 = 832 pavers.

Getting the base right

Almost every failed patio fails in the base, not the pavers. Excavate deep enough for base + sand + paver thickness, compact the native soil, then lay crushed stone with fines in 2–3 in. lifts, compacting each with a plate compactor. Slope the base, not the sand, about ⅛–¼ in. per foot away from the house. The sand layer is only a bed: keep it at about 1 in. and never use it to fill low spots.

Tips and common mistakes

  • Pull pavers from several pallets at once so slight color differences blend instead of showing as patches.
  • Start the pattern from a straight, square edge (usually the house) and snap lines every few rows.
  • Cut edge pieces no smaller than about a third of a paver; small slivers break loose.
  • Compact the pavers before sweeping in polymeric sand, then compact again and refill the joints.
  • Over clay soils, a geotextile under the base keeps the stone from pumping into the mud.

Want a price? The paver installation cost calculator uses published installed prices adjusted for your region. Need a step down at the edge of the patio? See the retaining wall calculator.

Ordering

Pavers are sold by the pallet or by the square foot; ask how many square feet a pallet covers for your style and whether part pallets are allowed. Order borders and soldier courses separately: they replace field pavers along the edge, so subtract their area from the field before counting.

Questions people ask

How many pavers do I need per square foot?
Divide 144 by the paver’s face area in square inches: 4.5 per ft² for 4 × 8 in. holland stones, 4 for 6 × 6 in., 2.67 for 6 × 9 in., 1 for 12 × 12 in., and 0.5 for 16 × 16 in. Then add waste for your pattern: about 5% for straight layouts, 10% for herringbone or 45° patterns, 15% for curves.
How much base gravel goes under pavers?
For patios and walks on typical soils, about 4–6 in. of compacted crushed stone; for driveways, 8 in. or more, and more on clay or poorly drained ground. Interlocking-pavement industry guidance (ICPI, now the Concrete Masonry & Hardscapes Association) and the paver maker’s instructions give the exact depth for your soil.
How much sand do I need for pavers?
A 1 in. screeded layer of coarse concrete sand under the pavers: 120 ft² needs 10 ft³, about 20 bags of 0.5 ft³. Joint sand is separate and goes on after the pavers are compacted.
How many bags of polymeric sand?
It depends on joint width, paver size and depth, so bags print a coverage chart. Wide-joint or tumbled pavers use far more than tight-joint pavers. Enter the chart value for your joint in the calculator.
Do I need edge restraint on every side?
On every edge that isn’t held by a wall, step or slab. Without it the outer pavers creep outward and the joints open up. The calculator uses the perimeter minus any length you mark as against the house.

Related calculators

All outdoor tools →