Exterior · Roof edge cost

Fascia & Soffit Cost Calculator

Fascia and soffit replacement priced by the linear foot from your roof edges, with your region applied.

Costs checked: November 2026Sources

1 Roof edges
ft
Horizontal edges with gutters
ft
Sloped gable edges
2 Location

Region factor ×1.00: U.S. national average. How it’s derived

Low
$1,770
Typical
$3,360
$20.98 per ft of roof edge
High
$4,920
Region
×1.00
U.S. national average
Cost breakdown
ItemQuantityLowTypicalHigh
Fascia board160 lin ft$1,120$2,340$3,520
Vinyl soffit100 lin ft$650$1,020$1,400
Total installed$1,770$3,360$4,920
The sources publish installed prices only for some lines here, so we don’t split those into materials and labor rather than guess.
Fascia 160 ft, soffit 100 ft. Rot repair in rafter tails or sheathing found during the job is billed on top; second-story work needs more staging.

Costs checked: November 2026. Ranges are published national figures (see Sources below) times the regional factor. They exclude permits, sales tax and unusual site work. Get at least three local quotes.

How the estimate works

Fascia and soffit are priced by the linear foot of roof edge. Fascia covers every edge, eaves and rakes; soffit normally covers only the eaves, unless the gable overhangs are boxed. The calculator multiplies each length by Angi’s published installed range and applies your regional factor. Angi publishes installed figures, so we don’t split materials and labor.

Fascia = (eaves + rakes) × $7 · $14.60 · $22 Soffit = eaves (+ rakes if boxed) × vinyl $6.50 · $10.20 · $14 or aluminum $8 · $14 · $20 × regional factor

Worked example

A ranch house with 100 ft of eaves and 60 ft of rakes, replacing fascia everywhere and vinyl soffit on the eaves: fascia 160 ft × $7 / $14.60 / $22 = $1,120 / $2,336 / $3,520; soffit 100 ft × $6.50 / $10.20 / $14 = $650 / $1,020 / $1,400. Total $1,770 / $3,356 / $4,920 nationally.

Why fascia and soffit fail

  • Overflowing gutters soak the fascia from behind. Clogged gutters and missing drip edge are the usual causes.
  • Ice dams push water up under the roof edge in cold climates.
  • Animals chew through soft or loose soffit to nest in the attic.

Choosing materials

  • Wood fascia is cheapest up front but needs paint; many installers wrap it in aluminum coil.
  • Composite or PVC fascia won’t rot and takes paint.
  • Vinyl soffit is economical and comes vented or solid.
  • Aluminum soffit is stiffer and more fire-resistant, at a higher price.

Planning gutters at the same time? Do them together: new gutters hang on new fascia. Price them with the gutter cost calculator.

Keep soffit vents clear when insulating the attic; baffles at each rafter bay hold insulation back so air can flow. The insulation calculator lists them.

Measuring the roof edges

Measure eaves along the gutter line, wall to wall plus the overhang at each end, and rakes along the sloped gable edge (or calculate them: the horizontal run of the rake times the pitch multiplier from the roof pitch calculator). For soffit, the price range covers typical 1–2 ft overhang widths; very wide overhangs use more material per foot.

Repair or replace everything?

Rot is often local, at gutter corners, below valleys and where downspouts attach. Replacing a few damaged sections and wrapping the rest can cost far less than a full replacement. If paint is peeling all around and the boards are soft in many places, full replacement with a low-maintenance material usually pays off. Ask for both prices.

Common mistakes

  • Covering rotten fascia with aluminum wrap without replacing the rot first.
  • Installing solid soffit where the attic relies on soffit intake vents.
  • Leaving gaps where animals can get in at the corners and rake returns.

Ventilation check

When soffit is replaced, it’s a good time to make sure the attic has enough intake vent area to match the ridge or roof vents, and that insulation isn’t blocking the vents. Vented vinyl or aluminum soffit panels provide intake along the eaves.

Questions people ask

How much does fascia replacement cost per foot?
Angi’s 2026 data puts fascia replacement at $7–$22 per linear foot including materials and labor, averaging about $14.60.
How much does soffit cost per foot?
Angi’s figures: vinyl soffit $6.50–$14 per linear foot installed (average about $10.20) and aluminum soffit $8–$20, for typical soffit widths.
What is the difference between fascia and soffit?
Fascia is the vertical board along the roof edge that the gutters hang on. Soffit is the horizontal underside of the overhang, between the fascia and the house wall, and usually includes vents that let air into the attic.
How do I measure for fascia and soffit?
Fascia runs along every roof edge: measure the eaves (the horizontal edges with gutters) and the rakes (the sloped gable edges). Soffit usually runs along the eaves only, unless the gable overhangs are boxed in.

Sources

Costs checked: November 2026. Each range is the published figure from the source named next to it; where we did arithmetic on a published figure the page says so. Regional factors: how they’re derived.

  1. How Much Does Fascia Cost? — Angi, checked Nov 2026.
  2. How Much Does It Cost to Install Vinyl Soffit? — Angi, checked Nov 2026.
  3. How Much Does It Cost to Install Aluminum Soffit? — Angi, checked Nov 2026.
  4. Cost vs. Value 2025: national and regional data — Remodeling magazine / Zonda (JLC), checked Nov 2026. Job costs for 13 projects in 9 Census divisions; used for regional factors and benchmark projects.

Related calculators

All exterior tools →